Drifta Parts - Frame

Front Connecting Arm/ Front Stub Axle/ Front Spindle for our single seater Drifta Go Karts (excluding Junior Drifta 80cc Go Kart).

Ideal for any DIY building project.

Compatible with our Front wheel hubs & tie rods. Shaft length 72mm Shaft diameter 17mm

Please note: The left side is the Left hand side when sitting in the drivers seat.

Price $35.90

Front Connecting Arm/ Front Stub Axle/ Front Spindle for our single seater Drifta Go Karts (excluding Junior Drifta 80cc Go Kart).

Ideal for any DIY building project.

Compatible with our Front wheel hubs & tie rods. Shaft length 72mm Shaft diameter 17mm

Please note: The right side is the Right hand side when sitting in the drivers seat.

Please note Castle/Axle nuts are sold separately as a pair.

Scroll down below this listing if you would like to purchase Castle/Axle nuts.

Price $35.90

AXLE BEARING (each)

UC 205

Inside diameter(ID) 25mm

Outside diameter (OD) 50mm

Comes with grub screws.

Compatible for use with our Rear Axle Shaft 880mm & 980mm

Ideal for any DIY project and suitable for 25mm axle.

Price $18.90

30mm thick in centre tapering to 25mm at end with spline.

Length: 880mm

23 points on splines

Length of splines: 95mm

Centre part of axle before step down is 525mm

Compatible with our own Drifta brand Go Karts (serial # LAKS... or YKHM2019...)

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Go Carts, Drift II Go Karts, Drift Trikes, Trolley's.

Ideal for any DIY building project.

Ideal if you are modifying your kart, home-built karts or other projects.

Price $90.00

30mm thick in centre tapering to 25mm at end with spline.

Length: 980mm 

23 points on splines

Length of splines: 145mm

Centre part of axle before step down is 525mm

Extra Long Rear Axle

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Go Carts, Drift II Go Karts, Drift Trikes & Trolley's.

Ideal for any DIY building project.

Ideal if you are modifying your kart, home-built karts or other projects.

Price $95.00

This Rear Axle Kit includes 1 x 880mm Axle, 2 x Rear Hubs, 1 x Brake Plate, 1 x Brake Hub, 1 x Chain Drive Sprocket, 1 x Chain Hub, 2 x Axle Bearings, 2 x Axle Spacer-Short, 2 x Castle Nuts.

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Go Carts, Drift II Go Karts, Drift Trikes,Trolley's  

Ideal for building/modifying your own Go Kart or any DIY project.

Price $295.00

This Rear Axle Kit includes 1 x 980mm Axle, 2 x Rear Hubs, 1 x Brake Plate, 1 x Brake Hub, 1 x Chain Drive Sprocket, 1 x Chain Hub, 2 x Axle Bearings, 2 x Castle Nuts, 2 x Spacers

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Go Carts, Drift II Go Karts, Drift Trikes, Trolley's. 

Ideal for building/modifying your own Go Kart or any other DIY project.

Price $299.00

To suit 25mm Axle, these are sold as a pair.

ID: 25mm

OD: 32mm

Width is 20mm.

Price $8.90

To suit 25mm Axle, these are sold as a pair.

ID: 25mm

OD: 37mm

Width is 50mm.

Price $15.90

Axle Nuts suitable for Rear Axle and Front Connecting arms ( ID:15mm).

Sold as a pair.

To suit our Drifta Go Karts.

Ideal for any DIY building project.

Ideal if you are modifying your kart, home-built karts or other projects.

Price $2.90

Bearing bracket/holder 

AVAILABLE IN BLACK COLOUR

The price is for 2 brackets only.

Inside diameter: 50mm

Distance between 3 bolt holes is 65mm.

Compatible with our Drifta brand Go Karts (serial # LAK) and components.

Ideal for DIY Drift Go Karts, Buggies, Trolleys.

Ideal if you are modifying your kart, home-built karts or other projects.

Price $19.90

Total length: 210mm

Eye to eye: 180mm 

To suit our own Drifta Go Kart frames starting with serial # LAKS... or YKHM2019...

Ideal for any DIY building project.

Ideal if you are modifying your kart, home-built karts, trolley's or other DIY projects.

Price $29.90

Total length: 210mm.

Eye to eye: 180mm
To suit Go Kart frames starting with serial # ZJLH.

Ideal for any DIY building project.

Ideal if you are modifying your kart, home-built karts, trolley's or other DIY projects.

Price $29.90

Throttle / Accelerator handle.

Attaches to our Steering wheel - Drifta (Butterfly style)

Used as a throttle handle for our Drifta brand karts with hand controls.

Can be used with a cable for a mechanical brake system (Rear Disc Brake Assembly).

Please note: This is not a handle for our Hydraulic brake units.

Price $19.90

Butterfly Style or Formula One Steering Wheel.

Please note colour of steering wheel is now BLACK not SILVER  (earlier models of DRIFTA karts)

340mm Across x 170mm Height

Distance between 3 mounting holes to attach to steering shaft is 33mm.

Compatible with our Drifta brand single seater Go Karts (excluding Junior Drifta 80cc Go Kart).

Attaches to Steering Column.

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Go Carts, Drift Trikes & Trolley's.

Ideal for any DIY building project.

Ideal if you are modifying your kart, home-built karts or other projects.

Price $39.90

Dimensions: 310mm Width x 260mm Height.

Distance between 6 bolt holes to attach to steering shaft/column is 35mm

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Go Carts, Drift Trikes & Trolley's.

Ideal for any DIY building project.

Ideal if you are modifying your kart, home-built karts or other projects.

Please note: centrepiece may be RED or BLUE

Price $49.00

Includes steering wheel, steering column with fittings and kill switch.

Please note colour of steering wheel is now BLACK

Compatible with all our Drifta single seater Go Karts (excluding Junior Drifta 80cc Go Kart).

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Drift Trikes & Trolley's.

Ideal for any DIY building project.

Ideal if you are modifying your kart, home-built karts or other projects.

Price $95.90

Steering column 540mm long.

Distance between 3 mounting holes to attach to steering wheel is 33mm.

Compatible with our Steering Wheel (Butterfly style) for our own Drifta brand karts.

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Go Carts, Drift Trikes & Trolley's.

Ideal for any DIY building project.

Ideal if you are modifying your kart, home-built karts or other projects.

Price $39.90

Steering column with fittings 540mm long.

Includes bottom plate.

Distance between 3 mounting holes to attach to steering wheel is 33mm.

Compatible with our Steering Wheel (Butterfly style) for our own Drifta brand karts

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Go Carts, Drift Trikes & Trolley's.

Ideal for any DIY building project.

Ideal if you are modifying your kart, home-built karts or other projects.

Price $59.90

Replacement bottom plate for steering column with fittings, and steering handle assy complete.

Attach to steering tie rod from steering column.

92mm length.

Price $9.90

DUST CAP for Drifta Go Kart wheels hubs.

The price is for 1 dust cap.

Price $5.90

Dust cap washer to suit Drifta Go Karts

Sold as a pair.

Price $2.90

Go Kart Seat

Approx. 440mm Across x 360mm Height

Compatible with all our Drifta single seater Go Karts excluding Junior Drifta 80cc Go Karts.

Heavy Duty Strong Flexible Plastic.

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Go Carts, Drift II Go Karts, Drift Trikes & Trolley's.

Ideal for any DIY building project. Ideal if you are modifying your kart, home-built karts or other projects.

Price $59.00

Seat cover padded with blue stripes.

To suit Drifta Go Kart Seat pictured above.

Price $48.00

Seat cover padded with red stripes.

To suit Drifta Go Kart Seat pictured above.

Price $48.00

Lap belt.

2 bolting points

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Go Carts, Drift II Go Karts, Drift Trikes & Trolley's.

Ideal for any DIY building project.

Ideal if you are modifying your kart, home-built karts or other projects.

Price $28.90

Harness 3 point seat belt.

These suit our Drifta brand single seater Go Karts (excluding Junior Drifta 80cc).

Easy adjustable straps to suit all sizes. 3 bolting points.

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Drift II Go Karts, Drift Trikes & Trolley's.

Ideal for any DIY building project.

Ideal if you are modifying your kart, home-built karts or other projects.

Please note: yellow strapping in photo may be black

Price $49.90

Long tie rod/Steering rack with ball/rose end joints.

These suit our Drifta single seater Go Karts (excluding Junior Drifta 80cc).

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Drift II Go Karts, Drift Trikes,Trolley's.

Ideal for any DIY building project. Ideal if you are modifying your kart, home-built karts or other projects.

These measure 615mm eye to eye.

Price $34.90

Short tie rod/Steering rack with ball/rose end joints.

These suit our Drifta brand single seater Go Karts (excluding Junior Drifta 80cc).

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Drift II Go Karts, Drift Trikes, Trolley's.

Ideal for any DIY building project. Ideal if you are modifying your kart, home-built karts or other projects.

These measure 310 mm eye to eye.

Price $28.90

Left hand & Right hand tie rod ends - Rose joints

These are sold as a pair, (1 x L/H and 1 x R/H).

Size of centre hole is 10mm

Thread size is 10mm

Material: Alloy steel

Replacement parts for our short & long tie rods (steering assembly), for our single seater Drifta karts (excluding Junior Drifta Go Karts).

Price $28.90

FRONT FRAME FOR DRIFTA GO KARTS 
Suitable for Sportz Drifta, Honda Drifta, Trail Blazer and Blazer Drifta Go Karts (non-caged karts).

Please note: These frames suit our own brand Drifta Go Karts.
Please specify the serial # on your Go Kart when ordering this part. (our own Drifta Karts are LAKS.. or YKHM2019.. ) 
Available in most kart colours, please specify your colour preference when ordering or Enquire if we have in stock.

Price $95.00

FRONT FRAME FOR CAGED DRIFTA GO KARTS

Suitable for Caged Trail Blazer Drifta 200cc and Ultimate Drifta 200cc Go Karts.

Please note: These frames suit our own brand Drifta Go Karts.
Please specify the serial # on your Go Kart when ordering this part. (our own Drifta Karts are LAKS.. or YKHM2019.. ) 
Available in most kart colours, please specify your colour preference when ordering or Enquire if we have in stock.

Our roll cages attach to this front frame.

Price $98.00

These are suitable for bolting front frame to mid frame.

Sold as a pair.

ID: 15mm 

Price $2.90

Attaches behind seat to main frame of our single seater Drifta karts (non caged karts).

Price $39.90

Complete Roll Cage.

Includes padding for bars ,and black fabric sun cover (not shown in photo).

Includes built-in comfortable padded head rest.

Comes as a kitset, just need to be bolted together.

These suit our own Caged Drifta brand single seater Go Karts (excluding Junior Drifta 80cc)

(Serial # LAKS... or YKHM2019...)

Suitable for Go Karts, Grass Karts, Off Road Go Karts, Drift II Go Karts, Drift Trikes, Trolley's.

Ideal for any DIY building project. Ideal if you are modifying your kart, home-built karts or other projects.

Price $229.00

Rear frame for our Drifta single seater Go Karts.

(Serial # LAKS... or YKHM2019...)

Also suitable for other DIY projects including Drift Trikes.

If this is for one of our Drifta Go Karts please advise which model as the engine mounting differs.

Centrifugal Dry Clutch 6.5HP Engine 

Wet Clutch 6.5HP Engine 

Wet Clutch 9.0 HP Engine

Please specify colour preference when ordering.

Price $159.00

To suit swing arm on Rear Frame. (pictured above).

We have 2 sizes available. Please check the size before ordering and specify which size you require.

Size 1: Length 42mm, Outside diameter 30mm, Centre hole 10mm (HR)

Size 2: Length 45mm, Outside diameter 25mm, Centre hole 12mm (HM)

Price $9.90

Fuel Cap

To suit 5.5HP, 6.5HP engines.

Price $15.90

Fuel Cap

To suit 5.5HP, 6.5HP engines.

External metal thread.

Price $15.90

To suit 5.5HP, 6.5HP engines.

Fuel tank capacity: 3.6L

Dimensions: 210mm x 250mm width x 100mm height

Price $52.00

To suit 9.0 HP 270cc engines.

Fuel tank capacity: 4.75L

Dimensions: 240mm x 270mm width x 150mm height

Please note: Image displayed is 6.5HP petrol tank.

Price $64.00

Steel Front Bumper Bar

Protects front frame and steering tie rods.

Easy to bolt on to front frame.

To suit our own Drifta karts with serial # LAKS.. and YKHM2019..

See image on left to see how it looks once fitted onto our go-karts.

Please click on image to enlarge.

920mm across.

Price $85.00

Replacement Number plate plastic back mounting & bracket.

To suit our single seater Drifta Karts.

Models: Trail Blazer Drifta, Sportz Drifta, Ultimate Drifta, Xtreme Drifta, Caged Trail Blazer Drifta Karts.

Price $25.90